BZ 3D A4988 Stepstick Stepper Motor Driver Module  with Heat Sink for 3D Printer Controller Ramps 1.4 MKS Gen L SKR V1.3 Board for 3D Printer Part(Pack of 5pcs)

-Intelligent chopping control that automatically selects the correct current decay mode (fast decay or slow decay) 
-Over-temperature thermal shutdown, under-voltage lockout, and crossover-current protection 
-Automatic current decay mode detection / selection 
-Internal UVLO
  -Mixed with slow current decay modes 
-Synchronous rectification for low power dissipation 
-Crossover-current protection 
-Thermal shutdown circuitry 
-3.3 and 5 V compatible logic supply 
-Thermal shutdown circuitry 
-Ground Fault Circuit 
-Load short-circuit protection 
-Of five optional step mode: full, 1/2, 1/4, 1/8 and 1/16

Chip upgrade Using the latest high-quality chips, higher compatibility and better conductivity.(It is believed that only high quality products can ensure the quality of your work and bring safety to your work.)

Product Features

  • Compared with ordinary A4988, our high quality A4988 drive production process is improved again by PCB gold plate process (gold-plated pin) SMT placement machine manufacturing, non-manual welding, higher yield and more stable performance.
  • Performance upgrade: PCB covering copper process upgrade to 2oz (our high-quality copper thickness 70um, ordinary 35um), higher copper content, better heat dissipation performance.
  • Under 2A current, it can work for a long time. It is very suitable for 3D Printer, Mendel, Huxley and other machines.
  • Using the latest chips, higher compatibility and better conductivity
  • Adjustable current control lets you set the maximum current output with a potentiometer, which lets you use voltages above your stepper motor’s rated voltage toachieve higher step rates.

Visit The Website For More Information…

BIQU SKR V1.3 Control Board 32 Bit Board Smoothieboard TMC2130 V3.0 for 3D Printer Parts SKR V1.3 MKS GEN L Ramps 1.6 Board

SKR Motherboard Parameters:
Appearance size: 110*85mm
Mounting size: 102*76mm
Microprocessor: ARM cortex-M3 CPU
Input voltage: DC12V-DC24V 5A-15A
Motor driver: support TMC2208, TMC2130, ST820, LV8729, DRV8825, A4988, can be independently external motor drive
Driver working mode support: TMC2130SPI, TMC2208UART
Motor drive interface: X, Y, Z, E0, E1, five (each has a reextendable interface), Up to 256 subdivisions
Display: 2.8 “TFT, 3.5” TFT, LCD2004, LCD12864

How to Use
The SKR motherboard connects with the computer via the [USB] interface. After the driver is installed, the motherboard can be inserted into the computer to recognize the port for data transmission. Without the driver installed, it is easy for the computer to not recognize the USB port

1. Smoothieware-usb-driver-v1.1 driver installation (Windows systems only) The driver can be obtained from our open-source network
Https://www.dropbox.com/s/ighnj7oa2l0bm5g/smoothieware-usb-driver-v1.1.exe?dl= 0
2. After installing the driver, connect the computer and SKR motherboard with USB cable
Note: When using smoothieware open-source firmware, since only Windows system drivers, the SKR board at this time can only be recognized by the Windows system port! ! !
3. If you are using Marlin2.0 firmware, follow the tutorial to install:
Tutorial:https://www.dropbox.com/s/ppjfflhf3j5yzh2/MarlinV2.0%20SKRV1.1%20instruction.docx?dl=0
Driver:https://www.dropbox.com/s/a0k5idjmf4fn82f/lpc176x_usb_driver.inf?dl=0
If you need more information about this Board please contact us

Package Included
1pcs SKR V1.3 Board
4Pcs TMC2130 V3.0
1pc USB cable

Product Features

  • Using 32-bit main frequency 100MHz ARM level Cortex-M3 series LPC1768 main control chip, the performance has been greatly improved
  • Reserved extended port SERVOS of PWM signal to support BL Touch
  • Support Resume Printing While Power Off,Filament Break Detection,Automatic Shutdown After Printing and other functions
  • The SPI working mode of the TMC2130 driver and the UART working mode driven by the TMC2208, which eliminates complex wiring process and can be used by simple unplugging jumper cap
  • SKR V1.3 board has CE Certification to adopt 4-Layer PCB with “Gold Finish” process which capability is more stable and better heat dissipation.

Visit The Website For More Information…

KeeYees Professional 3D Printer CNC Kit with Tutorial for Arduino, CNC Shield V3 w/Jumpers + UNO R3 Board + 4Pcs RAMPS 1.4 Mechanical Switch Endstop & DRV8825 GRBL Stepper Motor Driver Heat Sink

CNC Expansion Board:
-GRBL 0.9 compatible
-Runs on 12-36V DC
-4-Axis support: X, Y, Z
-It can drive 4 stepper motors, and each stepper motor only needs 2 IO ports.
That is to say, 6 IO ports can manage 3 stepper motors very well,
which is very convenient to use.

KeeYees UNO R3 Board:
-Microcontroller: ATmega328P
-Chip: ATmega16U2 
-Operating Voltage: 5V
-Input Voltage (recommended):7-12V
-Input Voltage (limit):6-20V
-Flash Memory: 32 KB of which 0.5 KB used by bootloader
-Digital I/O Pins: 14 Digital I/O Pins (6 PWM outputs)
-Analog Input Pins: 6 DC Current per I/O Pin 40 mA DC Current for 3.3V Pin 50 mA
-SRAM: 2 KB
-EEPROM: 1 KB
-Clock Speed: 16 MHz
Tips: Find more information about Arduino UNO R3 with the Expansion Board IO Port with our tutorial.

DRV8825 Stepper Motor Driver:
-Applied for driving stepper motors up to 8.2V-45V 2.5A
-4-layer PCB board (better heat dissipation)
-6 different step resolutions:
full-step, half-step, 1/4-step, 1/8-step, 1/16-step, and 1/32-step

Mechanical Switch Endstop:
-Length of Cable: 70 cm
-Red line — VCC (ramps of +)
-Black wire — GND (ramps of -)
-Green Line — SIGNAL (ramps in s)

Package Contents:
1 x CNC Shield Board
1 x KeeYees UNO R3 Board
4 x DRV8825 Stepper Motor Driver with Heat Sink
4 x RAMPS Mechanical Switch Endshop
20 x 2.54mm Black Jumper Caps
1 x 1.5m USB cable for UNO R3 Board

Product Features

  • 【KeeYees UNO R3 Board】 KeeYees UNO R3 Board uses the same ATmega328 and ATMega16U2 as official Uno R3 and 100% compatible with the official version. It comes with free 1.5m USB cable for convenient connection.
  • 【CNC Expansion Board with Free 20pcs Jumpers】This is the latest version of the expansion board, which can be used for engraving machines and 3D printers. It can drive 4 A4988/DRV8825 stepper motors. The jumper caps are necessary for CNC setups. You do not need to purchase this part extra.
  • 【DRV8825 Stepper Motor Driver w/ Heat Sink】DRV8825 is upgrade of A4988! It is a must-have module for 3D printers, CNCs and engraving machines. The 4-layer PCB board has better heat dissipation performance. 
  • 【Mechanical Switch Endstop】It uses a 22AWG wire that can withstand a current of 2A and a voltage of 300V. Better quality than traditional copper wire. It can reach the insulation temperature of 80℃. It is not easy to break, and very convenient to plug and remove.
  • 【Reliable technical support】If you don’t have a CD drive, please visit our website( www.keeyees.com ) to get relevant information or can contact us on Amazon, we will send PDF Document to you.

Click Here If You Need More Detailed Info…

WOWOONE CNC 3D Printer Kit for Arduino Mega 2560 R3 RAMPS 1.4 Controller LCD 2004 + 6X Limit Switch Endstop 5 A4988 Stepper Driver 3D Printerarduino arduino

CNC Shield Board:
1>PWM Spindle and direction pins
2>4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13)
3>2 x End stops for each axis (6 in total)
4>Coolant enable
5>Uses removable A4988 or DRV8825 compatible stepper drivers
6>Compact design
7>Stepper Motors can be connected with 4 pin molex connectors or soldered in place
8>Please note that this is an unassembled kit and Basic soldering skills are needed
A4988 Stepper Motor Driver:
1>Low RDS (On) Output
2>Automatic current decay mode detection / selection
3>Mix with slow current decay modes
4>Synchronous rectification for low power dissipation
5>Internal UVLO
6>Crossover-current protection
7>3.3 and 5 V compatible logic supply
8>Thermal shutdown circuitry
9>Ground fault protection
10>Load short-circuit protection
11>Five selectable step modes: full, 1/2, 1/4, 1/8 and 1/16
UNO R3 Board for Arduino:
1>MCU: ATmega328
2>USB interface: ATmega16U2
3>Operating voltage: 5V
4>Digital I/O pins: 14 (including 6 with PWM capability)
5>Analog input pins: 6
6>I-I/O pin output current: 40mA max
7>3.3V output current: 150mA max
8>Flash memory: 32kB (0.5kB used by bootloader- included)
9>Static RAM (SRAM): 2kB
10>EEPROM: 1kB
11>Clock speed: 16MHz
LCD 2004 Smart Controller
Easy connect it to your Ramps board using the “smart adapter” included.
After connecting this panel to your Ramps you don’t need your pc any more, the Smart Controller supplies power for your SD card.
Further more actions like calibration, axes movements can be done by adjusting the rotary encoder on the Smart Control panel.

Product Features

  • 3D Printer Accessories Set meets most needs. Including CNC Shield V3.0, UNO R3 Board, A4988 StepStick Stepper Motor Module.
  • The 3D printer stepper motor shield V3 can be used as driver expansion board for engraving machines and 3D printers.
  • It has in total 4 channel slots for A4988 stepper motor driver modules for driving 4 channel of stepper motors.
  • Each channel of stepper motor only needs 2 IO ports, which means 8 IO ports is sufficient to manage 3 stepper motors
  • This shield can make quick work for managing stepper motors in your project

Click Here If You Need More Detailed Info…